Skip to main content

Filter By:

  • Show More Brands

  • Show Fewer Brands
  • Show More Sizes
  • Show Fewer Sizes
  • Show More Model Years
  • Show Fewer Model Years

Tools

$2,935.99
The DT Swiss truing stand is the stand used by professionals. It is made of precision machined, polished, and anodized aluminum with hardened steel guides and mounts. - High-end quality and easy handling - Quicker wheel building - Compatible with all current bicycle wheels (12" – 29") with quick-release or thru-axle - Three precision multilink arms providing a wide range of contact points - Play-free precision gauges to measure lateral and vertical dish - Extremely stiff and solid clamping
$1,947.99
The PK-5 includes over 90 of our best shop tools selected with versatility in mind. A great way to outfit a pro bench or to set up a dream home workshop. The PK-5 is an impressive, professional set of specialty tools that can help you perform hundreds of bicycle repair and maintenance procedures. An investment you'll use and appreciate for decades. Kit Includes: - ATD-1.2 Adjustable Torque Driver - AWS-1 Three-Way Hex Wrench Set: 4, 5, 6mm - AWS-3 Three-Way Hex Wrench Set: 2, 2.5, 3mm - BBT-10.2 Adjusting Cap Tool: For 8-Spline Hollowtech II - BBT-22 Bottom Bracket Tool - BBT-69.2 Bottom Bracket Tool - BO-2 Bottle Opener - CBW-1 Open End Wrench: 8/10mm - CBW-4 Open End Wrench: 9/11mm - CC-4 Chain Checker - CN-10 Professional Cable and Housing Cutter - CNW-2 Chainring Nut Wrench - CP-1.2 Cassette Pliers - CT-3.3 Chain Tool - CWP-7 Compact Universal Crank Puller - DAG-2.2 Derailleur Hanger Alignment Gauge - DH-1 Dummy Hub - DP-2 Threaded Dummy Pedal - DSD-2 Derailleur Screwdriver: Cross Tip - DSD-4 Derailleur Screwdriver: Flat Blade - DT-2 Rotor Truing Fork - FR-5.2H Cassette Lockring Tool with Handle - GSC-1 GearClean Brush - HMR-8 8 oz. Shop Hammer - HXS-1.2 Hex Wrench Set - MLP-1.2 Master Link Pliers - NP-6 Needle Nose Pliers - PAW-6 6" Adjustable Wrench - PH-1.2 P-Handle Hex Wrench Set - PW-4 Professional Pedal Wrench - RR-12 Tape Measure - SBC-1 Spoke, Bearing and Cotter Gauge - SBS-1.2 Socket and Bit Set - SCW-13 13mm Shop Cone Wrench - SCW-14 14mm Shop Cone Wrench - SCW-15 15mm Shop Cone Wrench - SCW-16 16mm Shop Cone Wrench - SCW-17 17mm Shop Cone Wrench - SCW-18 18mm Shop Cone Wrench - SCW-19 19mm Shop Cone Wrench - SP-7 Side Cutter Pliers - SW-0 Precision Spoke Wrench: .127" - SW-2 Precision Spoke Wrench: .136" - SWR-8 3/8" Drive Ratchet Handle - SZR-1 Shop Scissors - TL-1.2 Tire Lever Set - TL-4.2 Tire Lever Set - TL-6.2 Steel Core Tire Levers - TWS-1 Torx Compatible Wrench Set - UP-SET Utility Pick Set - VC-1 Valve Core Tool - ZP-5 5" Flush Cut Pliers
$1,649.99
- Well thought out, extremely durable tool pallets organize and hold your tools in place. Pockets are designed with the size of our tools in mind. It also features a few extra pockets leaving you room to personalize your kit. - 48 pieces of our tools that are a perfect fit for a portable set, shop, home or team mechanics
$959.99
- Swiss made, high precision spoke tension instrument - Measures spoke tension for all types of spokes (including bladed, butted, Ti, etc.) - Aluminum construction with precision dial - Includes injection molded plastic storage case and (Nm)-calibration chart
$839.99
The DT-5.2 is engineered and built to accurately face front or rear disc brake mounts so they are precisely aligned to the rotor. - Faces any IS Mount, Post Mount, or new Shimano Flat Mount, including low clearance, chainstay mounts - Telescoping axle adaptors allow use with any configuration of open or thru-axle dropouts and dropout widths (including Boost 110, Boost 148 and all fat bike axles) - Includes two facing cutters: IS Mounts Post and Flat Mounts - Includes storage case
$809.99
The SHX-1 Slide Hammer Extractor is a professional solution specifically designed for removing press fit cartridge bearings from bicycle components. Utilizing expanding collets, an extendable shaft, and a substantial (960g) slide hammer, the SHX-1 securely yet forcefully drives out cartridge bearings with targeted impact. The SHX-1 is compatible with cartridge bearings with inner diameters from 6 to 32 millimeters, covering most press fit applications found on bicycles including hubs, suspension linkages, and bottom brackets. - Set of 5 expanding collets covers most bicycle bearing IDs from 6mm to 32mm - Slide hammer shaft is extendable from 6.5" (165mm) to 13" (233mm) for additional force when needed - Organized in a convenient storage case
$771.99
The BBP-AOS is used in conjunction with the BBP-1.2 Bottom Bracket Bearing Press Kit to extract press fit bottom bracket bearings, cups, and adaptors. The BBP-AOS utilizes an expanding collet and extractor cup system to safely remove bearings without requiring impact. Also included are eight installation drifts for pressing bearings into pre-installed cups. - 8 precision-machined extractor cups and 5 hardened collets for compatibility with most bearing IDs and bearing/cup ODs - 8 installation drifts for standalone bearing installation - Organized in a convenient storage case - Full list of compatible bearing inner/outer diameters found on instructions/parts diagram NOTE: The BBP-AOS requires the BBP-1.2 Bottom Bracket Bearing Press Set for use. The BBP-1.2 and BBP-AOS are also available as a complete set (part # BBP-2).
$690.99
Redesigned! We've made the base stronger for better stability. One-size-fits-all conical thru-axle adapters are now included with the stand, and are held in place by magnets when not in use. The arms have been made longer to accommodate 29+ wheels better and the calipers widened accordingly. Threads, springs and bearings were all revised resulting in smoother operation plus less frequent calibration. Additionally, we include white high-gloss stickers you can apply to the base and caliper arm to improve background contrast, making it easier than ever to use. -Stronger base for improved precision -Longer and redesigned upright arms for improved clearance of 29+ wheels -Wider calipers for increased clearance of 29+ wheels -Accommodates wider axles, works with through axle hubs up to 197mm width (include the use of adapters). Max. arm opening 230mm (without the use of adapters). -New bearings on the upright arm adjust axle are spring loaded for improved precision and reduced frequency of calibration -Redesigned caliper tips for easier radial truing -Revised threads and springs for smoother operation -8mm bench mount holes at the bottom, 268 mm center to center -Slicker design, all black. Includes white high gloss stickers, covering the base and caliper arm, for improved background contrast (stickers are not preapplied) -Comes with conical magnetic through axle adapters – one size fits all (12, 15 and 20). The adapters are now magnetic and can be affixed anywhere on the base. Features a bolt for more permanent fix on the upright arms. Compatibility: -Accepts wheels from 16 to 29+ inch with or without tire. Supports solid, quick release and through axle hubs -Accepts hubs up to 197mm when using our thru axle adapters, 230mm without. -Through axle hubs are supported with use of the adapters (included) -One pair of through axle adapters support all sizes of through axles
$613.99
The SBK-1 is a professional level kit for installing and removing cartridge bearings in bicycle suspension pivots. A comprehensive set of 27 precision-machined hard-anodized guides enables compatibility with a wide range of bearing inner and outer diameters. Combined with our proven bearing press design, the SBK-1 quickly and easily pushes the old bearing out of the linkage and reinstalls the new bearing precisely and squarely. - Magnetic back plate for easy configuration and assembly - Organized in a convenient storage case Includes extractor cups/drifts for the following ODs: - 16mm - 17mm - 19mm - 20.6mm - 21mm - 22mm - 22.3mm - 24mm - 26mm - 28mm - 28.6mm - 30mm - 32mm - 35mm Includes extractor studs and pilots for bearings with the following IDs: - 8.5–9mm - 10mm - 12mm - 12.7mm - 15mm - 17mm - 20mm NOTE: For bearing extraction, the SBK-1 requires a minimum of 3mm of flat linkage structure outside the bearing to support the extractor cup/drift. For bearings without this flat structure, consider using the Park Tool SHX-1 Slide Hammer Bearing Extractor.
$510.00
To achieve maximum suspension performance, proper setup and tuning is essential. Go to www.rockshox.com/app for suggested air spring pressure and rebound damper settings for your fork. Go to www.sram.com/service for additional product and technical information. Air spring pressure and coil spring tables are available in the RockShox® Front Suspension Oil, Air, Coil, Token, and Specification documents. For a complete list of available coil springs and Bottomless Tokens™, consult the RockShox Spare Parts Catalog. Consult the RockShox service manual for your fork for complete disassembly and assembly procedures. Tuning suggestions are starting points. It may take trying various adjustments to find the settings that work best for each individual rider and trail condition. - Includes complete right-side internals
$510.00
To achieve maximum suspension performance, proper setup and tuning is essential. Go to www.rockshox.com/app for suggested air spring pressure and rebound damper settings for your fork. Go to www.sram.com/service for additional product and technical information. Air spring pressure and coil spring tables are available in the RockShox® Front Suspension Oil, Air, Coil, Token, and Specification documents. For a complete list of available coil springs and Bottomless Tokens™, consult the RockShox Spare Parts Catalog. Consult the RockShox service manual for your fork for complete disassembly and assembly procedures. Tuning suggestions are starting points. It may take trying various adjustments to find the settings that work best for each individual rider and trail condition. - Includes complete right-side internals
$430.00
Many athletes are fortunate enough to be able to ride nearly anything. For those that are sensitive to bike fit though, replicating fit to a new bike or confirming fit after travel can be a challenge involving lots of trial and error. This set of tools allows accurate and repeatable measurements for saddle height, angle and setback. The accuracy and repeatable measurements also serve as a base to make adjustments to fit. -The magnetic saddle height bullets ensure you get an accurate center at the BB by locating in the crank arm fixing bolt or the crank arm preload cap of Shimano caps. This allows you to focus on the smart end of the tape measure at the saddle plate. -Two reference marks on the saddle plate means you can pull a measurement to the exact same spot relative to the nose of the saddle every time. This gives you accuracy down to a single millimeter. -The front of the saddle plate is engraved with a ruler, to allow you to calculate saddle setback at the saddle. This allows you to drop the plumb bob off the side of the bike and clear all of the bottle cages. -The wide plate has ample room to mount a level, protractor or smart phone for adjusting the angle of the saddle. This is particularly helpful for non traditional saddles like SMP and Adamo.
$420.99
- Crank Saver—Pedal thread repair and insert kit - Includes: left and right reaming tap 5/8x24 TPI, 10 pedal thread inserts for left crank arm, 10 pedal thread inserts for right crank arm, metal box with cut out SOS foam trays.
$407.00
To achieve maximum suspension performance, proper setup and tuning is essential. Go to www.rockshox.com/app for suggested air spring pressure and rebound damper settings for your fork. Go to www.sram.com/service for additional product and technical information. Air spring pressure and coil spring tables are available in the RockShox® Front Suspension Oil, Air, Coil, Token, and Specification documents. For a complete list of available coil springs and Bottomless Tokens™, consult the RockShox Spare Parts Catalog. Consult the RockShox service manual for your fork for complete disassembly and assembly procedures. Tuning suggestions are starting points. It may take trying various adjustments to find the settings that work best for each individual rider and trail condition. - Includes complete right-side internals
$391.00
The lightest production damper. Ever. Performance packed with a rock-solid lockout to power up climbs and smash through sprint finishes. - Every detail machined and optimized to save on weight and maximize your performance - Factory tuned compression (in open position) provides the highest level of XC performance, precision and control - Maximum efficiency with a rock-solid lockout
$374.99
- Hub bearing press set with 10 guides - For ID 8-20mm
$351.99
The 2197 is an add-on accessory for the Park Tool DT-5 and DT-5.2 Disc Brake Mount Facing Set to enable easier and more efficient facing of disc brake mounts on carbon fiber frames. Features a brazed-on diamond grit surface that is over 100 times more durable and effective on carbon fiber than the cutter included with the DT-5.2. The 2197 sits between the cutter of the DT-5.2 and the brake mount, and smoothly and evenly grinds the mounting surface until it is flat and properly perpendicular to the rotor. NOTE: The 2197 is intended for facing carbon fiber only. Aluminum, steel, and titanium disc brake mounts should be faced using the #2171 facing cutter included with the DT-5.2. For carbon frames that feature aluminum inserts (with a carbon/aluminum hybrid mounting surface), use the #2197. When machining carbon fiber, regularly apply water (or a similar solution) to the cutting surface.
$336.99
Click-Torque wrench in the unmistakable, robust Wera design with high accuracy. Easy setting and saving of the default value. The audible and tactile clicks on reaching the scale values also facilitate the safe setting of the desired torque value. For right-hand use (clockwise torque control) and with 45-tooth reversible ratchet mechanism. - With 1/4" square drive, reversible ratchet, 45 teeth - Easy setting and saving of the desired torque value with audible and tactile clicks when reaching the scale values - Audible and tactile release mechanism when the set torque value is reached - Measuring range: 2.5-25 Nm; Precise to +/- 4% - Designed with ergonomic 2-component handle suitable for right-hand use
$329.99
- Tool for pulling and pressing bottom bracket bearings. - For all BB30 frames and bearings - Allows the bearing to be pulled without damage for cleaning and re-greasing - Also safely presses bearings back into cups - Instructions included
$319.99
- Removes bearings from hubs and various other items - Works on bearings with an internal diameter of 8-32mm
$304.99
Precision-machined anodized aluminum clamps designed to allow for easy and secure clamping of round suspension components during service. Designed by Barnett Bicycle Institute and manufactured by Wheels Manufacturing. Kit includes 3 pairs of shaft clamps to fit 15 shaft diameters from 8mm to 28.6mm For use with: - Suspension damper shafts - Suspension damper cylinders - Suspension air-spring cylinders - Suspension piston shafts - Thru-axles Clamp 10-006 fits - 8mm - 9mm - 10mm - 12.7 - 15mm - 15.9mm - 16.7mm Clamp 10-007 fits - 17.5mm - 18.7mm - 19.5mm - 21mm - 22.2mm Clamp 10-008 fits - 23.8mm - 25.4mm - 28.6mm
$300.00
Turbo S Diagnosis Tool from Specialized.
$299.99
- Installation and removal tool for press fit BB86 and BB92 bottom brackets
$297.50
The unique thing about our Saw Guide is that the clamp is open, so you can slide it around the steer tube instead of having to slide it over the end. It doesn't sound like that big of a deal but it means you can get an accurate and square cut without taking the fork off the bike and more importantly without taking all the cables out of the bike. Use this tool once for that application and it's paid for itself. Of course it will work on normal steer tubes as well and give you a nice square cut every time. The guide is two sided, one side for standard toothed metal cutting blades and the opposite side is wider for abrasive blades used to cut composites. You can also use the guide in a vise like you're probably use to and it's pretty compact if you want to travel with it. Compatible with 1" and 1.125" steer tubes Currently not compatible with cutting handlebars!
$290.99
Joker Combination Wrench Set
$289.99
- The Pro bearing punch tool-kit allows fast removal of bearings in suspension linkages and hubsets. - The steel punches locate on the inside diameter of a bearing in order to drive the bearing out of the bore. - The bearing punch kit includes 8, 10, 12, 15, 17, 18 and 20mm sizes and include a tool roll for organized shop use and travel.
$285.99
- Drift and over axle set for less common thru axle hube and frame bearings - For use with 3/8" press rod - See wheelsmfg.com for full list of contents
$271.99
The Headset Press Pro Install Kit is a robust, and easy to use tool. The kit includes a machined aluminum handle, 1/2" threaded rod, two machined aluminum drifts and the adjustable press stop allowing for easy drift placement. One drift is machined with multiple steps to fit common head tube inner diameters listed in the compatibility tab below. The other drift has two sizes to press in cups with either 1-1/8" or 1-1/2" bearings. - machined aluminum handle and drifts - red anodized drifts and handles - zinc-plated 1/2" diameter threaded rod - long threaded rod works with long head tubes up to 250mm includes - 1 head tube drift includes - 1 headset cup drift - 1 adjustable press stop - 1 threaded handle includes on 1/2"-13x17" unc threaded rod
$269.99
The BKM-1.2 Hydraulic Brake Bleed Kit will bleed most models of mineral oil-based hydraulic bicycle disc brakes, including models made by Shimano®, Magura®, TRP®, Tektro®, Trick Stuff®, SRAM® DB8, Campagnolo®, Promax®, and Clarks®. Bleeding of hydraulic brakes removes air bubbles and contaminants from the braking system, for long-lasting components and peak performance. The BKM-1.2 is built for the rigors of daily commercial use and includes two syringes, hoses with shutoff clips, multi-size bleed blocks, a bleed funnel, and a set of our unique mountable syringe holders, as well as multiple hose fittings to fit the multiple standards found on hydraulic bicycle brake systems. Every part is replaceable and available from Park Tool. Housed in a rugged storage case. Includes: -  Two 20 mL syringes -  Two hose assemblies with shutoff clips -  One hose assembly with integrated fitting for bleed nipples such as those found on Shimano® mineral oil brake systems -  One open-ended hose assembly -  Bleed funnel with stopper -  Two 10 mm/12 mm universal bleed blocks -  Two 11 mm bleed blocks -  Two adjustable syringe holders -  M4 x 0.7 adapters — SRAM® DB8, Trick Stuff®, Campagnolo® (x2) -  M5 x 0.8 adapter — Formula™ Cura™, Tektro®, Hayes® (x2) -  M6 x 0.75 adapter — Magura® -  M6 x 1.0 adapters — universal (x2) -  M6 x 1.0 adapter — Promax® -  M7 x 0.75 adapter — Shimano® -  Hose compression sleeve — universal -  Fluid disposal bag -  Set of spare O-rings and hose -  Replacement parts available -  Brake fluid not included NOTE: The BKM-1.2 is for mineral oil-based hydraulic bicycle brake systems only. DOT fluid and mineral oil should never be mixed in the brake system or in their respective service tools. Cross-contamination of brake fluid may cause seal failure which may result in brake failure. For brakes using DOT fluid use the Park Tool BKD-1.2 Hydraulic Brake Bleed Kit — DOT.
$268.99
- Advance bottom bracket bearing extractor set - (1) BE-22mm, (1) BE-24mm, (1) BE-29mm, (1) BE-30mm, (1) Bearing Pusher, (1) 39mm sleeve, (1) 42mm sleeve, (1) 44mm sleeve, (1) receiver cup
Page 1 of 16 Next page