If you've heard the expression "to Stan's a tire," it's referring to Stan's Tire Sealant. Put the recommended amount in your road, mountain and cyclocross tires and it will stop slow leaks and seal small punctures. Rim strips and valves not included.
$20.99 - $22.99
You'll ride with peace of mind when you pack a can of Vittoria's Pit Stop Tire Sealant. It contains pure latex foam sealant and compressed air to quickly inflate and repair your tire so you can get on with your ride. Available in three sizes for varying tire volumes: - Road Racing: inflates 21-28-inch tubulars up to 94 psi and 700c clinchers up to 87 psi so you can ride, instead of walk to the closest pump and top off the tire to full pressure. - MTB 50 mL: Repairs and inflates low-volume MTB tires in less than a minute. - MTB Magnum 75 mL: Repairs and inflates meaty 27.5-inch tires and cross country 29-inch tires in less than a minute.
The Next Level in Sealing Power from the People who Invented Tubeless Conversions If you've walked the mechanics' pits at any National or International level event, chances are you've seen them: trademark Stan's black quart bottles with no labels. Look closer and you might have seen strange symbols scrawled all over the bottles in a silver marker, letters and numbers, formula notes by the man himself, Stan Koziatek. For nearly fifteen years Stan has been quietly formulating a special racing version of our legendary sealant for many of cycling's most successful teams. Working with athletes who push themselves and their tubeless systems to the absolute limit, he developed a proprietary sealant formula with close to twice the amount of the standard sealing crystals plus special "XL" crystals capable of sealing even larger punctures. Stan's Race Sealant's combination of large and smaller sealing crystals interlock to form a lattice work that not only seals but strengthens and reinforces the area of the puncture, allowing for an entirely new level of sealing performance. The quantity and size of crystals in this special formula means that Stan's Race Sealant can only be installed directly into the tire. As a result of its immense sealing capabilities, the Race Sealant will clog injectors and smaller bottles almost immediately. Stan's has made Race Sealant available to riders everywhere, and it is only available by the quart. - First choice of riders around the world for tubeless conversion and flat prevention - Twice the amount of Stan's standard sealing crystals - "XL" crystals capable of sealing even larger punctures - Stays liquid 2-7 months for long-lasting protection - Premium low-viscosity formula resists freezing to work in environments as cold as -30° F (-34° C) - Natural materials, safe for the environment
$5.99 - $39.99
The Product that Started a Tubeless Revolution Inside this simple bottle is a product that changed cycling. Today's tubeless systems rely on the lighter, more reliable, self-sealing performance of Stan's Tire Sealant. Just two ounces of Stan's in a converted standard tire or tubeless tire can repair punctures up to 1/4-inch almost instantly to keep you rolling. Longer-lasting Stan's Tire Sealant is formulated to stay liquid in tires with even thin casings for up to seven months. Arid conditions require more frequent monitoring of sealant levels, but anti-freezing agents in our special formula allow Stan's Tire Sealant to be used in temperatures as cold as -30° F. One quart will convert up to 16 tires. - First choice of riders around the world for tubeless conversion and flat prevention - Seals punctures up to 1/4-inch (6.5mm) quickly - Stays liquid 2-7 months for long-lasting protection - Premium low-viscosity formula resists freezing to work in environments as cold as -30° F (-34° C) - Natural materials, safe for the environment - Can be injected through valve stems with removable cores compatible with tubes and tubular tires
If you've heard the expression "to Stan's a tire," it's referring to Stan's Tire Sealant. Put the recommended amount of this liquid sealant in your road, mountain, and cyclocross tires and it will stop slow leaks and seal small punctures.
Special assembly liquid for bicycle tires. A practical sponge applicator allows the liquid to be applied to the tire bead very simply - without smudging fingers. When inflating, the tire bead slides easily into the correct position on the rim. The liquid evaporates completely after about 10 minutes!
PROCORE is an inner high-pressure air chamber for tubeless systems that allows dual air pressures for traction and impact protection. Procore allows low pressures (down to 14psi) to be run in tubeless tires, with a high-pressure inner chamber that locks the bead in place and prevents burping and rim dents from impacts. - Sold as a set with all components to set up a wheelset on one bike (tires not included) - Minimum internal rim width is 23mm - Maximum distance from rim well to rim inner surface is 20mm - Minimum tire pressure with ProCore is 14psi
These oversized Presta valve nuts are specifically designed to provide extra clearance and extra leverage to better tighten tubeless valves. They're especially helpful on single-wall rims. -Concave to allow better engagement of the valve/rim interface -Oversize to provide extra torque when tightening -Especially helpful on single-wall rim tubeless setups -CNC-machined AL-6061
A removable 60mm valve extender for use with deep-section rims
A new standard in tubeless sealant. Finish Line Tubeless Tire Sealant, featuring Fiberlink technology, will not cure inside the tires and doesn’t need to be refreshed every few months to maintain effectiveness. This sealant will last the entire usable life of the tire. Since there is no liquid latex or ammonia in Finish Line sealant, it is naturally non-toxic, hypoallergenic and safe for carbon fiber rims. Additionally, Finish Line Tubeless Tire Sealant cleans up easily with water – no more scrubbing or scraping cured latex from tires and rims. Fiberlink technology makes this possible. Utilizing DuPont Kevlar fibers, Fiberlink seals are extremely robust once they plug a hole. When a puncture happens, fibers rush into the wound and quickly stop air loss. As the tire flexes while it is ridden, the Fiberlink mesh tightens and reinforces itself, creating a confidence-inspiring seal that will last ride-after-ride. - Non-latex ammonia-free formulation - Kevlar reinforced Fiberlink mesh seal - Seals up to 1/4" punctures - Can be used in extreme temperatures, down to -10 degrees Fahrenheit
- Specific DT-Swiss tubeless ready valve stems for tubeless applications
Continental's Easy Tape Rim Strips are 20mm wide and are made of a tough, elastic and waterproof, non-adhesive nylon. This makes they quick and easy to install. Just stretch them over your rims and let them snap in place! Each box contain a pair of rim strips.
This is Continental's glue for gluing tubular ("sew-up") tires on aluminum tubular rims. The container has a brush built into the screw-on cap for easy glue application. You get enough glue to install about 12 tires.
Continental Carbon Rim Cement adheres to carbon fiber rims better than standard tire glue. This is Continental's glue for gluing tubular ("sew-up") tires on carbon tubular rims. - This 200g Can has a brush built into the screw-on cap for easy glue application.
Continental's Valve Extenders are made of durable aluminum and come in four sizes so you can attach your pump to your valve, no matter how deep your rims are.
This item contains 10 replacement plugs for the Blackburn Plugger Tubeless tool (sold separately), a one-shot tire plugging system for tubeless tires. It deploys in seconds to give a permanent fix for your flat.
Those guys who said "Tubeless tires never get punctures"? They lied. The Blackburn Plugger Tubeless Tire Repar Kit is a quick, one-shot tire plugging system for tubeless tires. It deploys in seconds to give a permanent fix for your flat. Mount it to your frame, tape it to your top tube, or strap it to your ankle like a shark knife. Just keep it close and it'll get you out of trouble. Pronto. - Stores ten plugs. - 27g tool only 47g tool with strap
The 45NRTH stud tool seats and removes the stud from the stud pocket. Customize your stud tread pattern or replace missing studs. Works with all 45NRTH studdable and studded products. Aluminum carbide studs sold separately. - POM-injected handle - Stainless steel barrel - Thumb and index-finger grips for more comfort and control - Compatible with studs that have a 3.5mm or smaller shaft
Page 1 of 1