Tools/Maintenance

One of the only bits of maintenance an internally geared hub needs is occasional oiling. Using the proper oil is essential, and, if you have a Shimano Alfine hub, you've found the right stuff. - Mineral oil based lubricant specifically for the Alfine 11-speed hub

- A biodegradable degreaser that cuts through the toughest grime - Strong enough for the metal parts, Yet safe enough to clean parts with rubber o-rings and seals, urethane elastomers, and painted surfaces - Exceeds all federal V.O.C. and California carbon regulations - Law prohibits ORM-D materials from shipping by air

Finish Line Showroom Polish is made with Teflon fluoropolymer and uses DuPont Teflon Surface Protector technology. Provides a brilliant shine plus long term protection on all surfaces of a bicycle. 100% safe for all plastics, rubbers and carbon fiber parts.

The MT-10, 20, 30 and 40 are high quality folding take-along tools that feature forged aluminum side plates, a mix of hardened and plated tools, and smooth ergonomic operation.

PRO X Freehub Grease, using our MRCC Micro Resistant Complex Compounds, is specifically designed for all freehubs that require a very lightweight grease. Non-pawl freehubs recommend a grease to stay in the mechanisms moving parts. Oils generally are to thin and will move away from moving parts leaving them exposed to wear and malfunction due to lack of lubrication. PRO X Freehub Grease performs in a broad temperature range from the summer heat to the extreme cold temperatures. "Pour Point" of PRO X Freehub Grease is -30F / -34C degrees. PRO X Freehub Grease works exceptional in hubs that share lubrication between the freehub and wheel bearings. Follow the manufacturer's specification for the volume required in your freehub body to experience the superior performance of Dumonde Tech's PRO X Freehub Grease. Our MRCC Micro Resistant Complex Compounds have been in development for over 10 years by Dumonde Tech Design Group. MRCC technology provides premium lubrication by reducing friction better than other lubricants. Lighter viscosity while maintaining high protection. The increase in adhesion creates higher film strength. Originally developed for our Motorsports lubrication, MRCC, is incorporated into our revolutionary PRO X bicycle lubricants. Everyone who has tested or raced using PRO X reports that its performance is significantly better than any other lube they have ever used. Benefits: - Performs in cold conditions. Ideal for Snow Bikes - Reduces resistance - Reduces watts used. - No shipping restrictions, can be sent anywhere in the world by air or ground. - No VOC's.

Service kits include dust seals, foam rings, oil seals, air and damper o-rings needed for basic service.

The Masterlink Pliers is a multi-tool developed to provide functions that are not on a typical multi-tool. It is designed to be light and compact so you can carry it with you. This tool serves as a tire lever, valve core remover, valve stem lock nut wrench, and master link pliers. It also provides storage for two master links so you will always be prepared on the trail. Magnets hold the master links securely in place and self close the tool. - Weight: 38.5g - Size: 116 mm x 20 mm x 9 mm - Material: 7075-T6 aluminum - 9, 10, 11, and 12-speed master links and chains - Compatible with SRAM PowerLock Link, Shimano Quick-Link, KMC Missing Link and other similar master links

For extreme conditions, you need an extreme lube. That's when you grab Finish Line's Wet Lubricant. It's ultra water-resistant and long-lasting thanks to its special formulation of synthetic oils, special polymers and anti-wear additives. This lube delivers superb drivetrain lubrication and protection and it's the ultimate choice for muddy off-road rides, all-day epics and long, rainy commutes. - Formulated with high viscosity synthetic oils, water repelling polymers, and advanced anti-wear additives - Will require more attention to drivetrain cleanliness, but delivers the ultimate in lubricity and protection - Upon application, wipe excess off chain to minimize attraction of dirt and grime - Finish Line's Wet Lubricant delivers the ultimate in lubricity and protection. It requires a little more attention to drivetrain cleanliness compared to Finish Line's Dry or Wax lubes.

The Switch Tool has evolved. We've all heard "if it ain't broke, don't fix it", but what if riders just want to fix more things? Enter the Big Switch, the larger sibling to the hit Switch tool. This new, compact, and super functional tool kit includes essentials you’ll find on the Switch including T25 and T30 torx bits, 2.5, 3, 4, 5, and 6mm allen bits, and a flathead screwdriver. The Big Switch also features an 8mm hex tool, and a chain breaker. The chain breaker handle includes size 0, 1, and 2 spoke wrenches, a disc pad spreader and a Presta valve core tool. Individual T or L handle tools let you access tight places and give you more leverage on bolts and screws. Go ahead, fix everything. - 15 functions - Includes T or L handle wrenches. - Tool bits include: T25, T30, 2.5mm, 3mm, 4mm, 5mm, 6mm, 8mm, and a flathead. - Pocket sized nylon carrying pouch includes a stash for your I.D., credit card, and cash. - 134g

Can you tell the difference between 15psi and 17psi? No you can't. We can't either, but Blakburn's digital gauge can. Today's wider, lower pressure tires are more pressure-critical than back when we just used to put as much pressure in as the pump could stand. It's not about fending off flats these days, it's about grip. And the difference between too much and not enough can be as little as a couple of pounds of pressure. The days of "giving it a squeeze" are over. - Swivel/Dual Head - Backlit Display - Accurate within 1% of pressure - Rated from 1-150 PSI - Key Chain Loop - 0.30lbs

- Installation wrench for all Enduro TorqTite Bottom Brackets - Some TorqTite installations require two wrenches

Prepares surface, accelerates curing and promotes maximum performance of Park Tool TLR-1 and TLR-2 Threadlockers as well as RC-1 Retaining Compound. Notice: Must be used on all component, fastener and carbon fiber surfaces in conjunction with threadlockers and retaining compounds that contact carbon fiber such as PF30 bottom brackets or brackets or bearings pressed into carbon fiber frames. Failure to do so could result in permanently bonded parts.

The BK-UK includes six new and revised parts for the Park Tool BKD-1 and BKM-1 Hydraulic Brake Bleed Kits, allowing for compatibility with the latest brake models from popular manufacturers. Includes: - Part #2600A (x2) — M4 x 0.8 adaptor for use with SRAM DB8, Trick Stuff, and Campagnolo mineral oil brake systems - Part #2588.2 — Thin-walled hose compression sleeve for internal bleed nipples, such as those found on Shimano mineral oil brake systems - Part #2574A — Hose assembly with integrated fitting for bleed nipples such as those found on Shimano mineral oil brake systems - Part #2615-2 (x2) — 11 mm bleed blocks for use with Hayes DOT brake systems All parts also available individually. NOTE: The seals on each part are designed for one type of fluid — DOT fluid or mineral oil — and should be used only on the systems they were intended for. DOT fluid and mineral oil should never be mixed in the brake system or in their respective service tools. Cross-contamination of brake fluid may cause seal failure which may result in brake failure.

Professional quality T-Handle hex wrench built for speed, efficiency, leverage and a perfect fit. - Carefully selected combination of Chrome Vanadium and S-2 tool steels - Unique anodized aluminum Speed Spinner makes running long bolts in and out quick and effortless - Machined, chamfered tips allow easier insertion into hex fittings - Integrated “Strip-Gripper” twisted hex that makes removal of most bolts with stripped or oversized hexes fast and easy - Sliding T-handle creates increased leverage and multiple access positions

- The wrench is used to remove and install Shimano Hollowtech II, Campagnolo Ultra-Torque and Power Torque, Race Face, FSA, SRAM, Truvativ, Chris King bottom brackets - Small wrench is included for removal and installation of Shimano plastic bolts that are used on the Hollowtech II cranksets - Material: premium flex plus carbon steel, Surface finish: chrome plated according to ISO1456:2009

Finish Line's Mineral Brake Fluid is formulated specifically for bicycle brake systems requiring mineral oil. Features no compromise leading edge chemistry to provide superior fluid life and braking performance. Formulated with a low viscosity base oil to yield superior level response, pad retraction, and consistent performance through a full range of operating temperatures. Finish Line Mineral Brake Fluid was specifically engineered for use in bicycle hydraulic disc brake systems. When you are serious about getting the most out of your braking system, Finish Line Mineral Brake Fluid is a great choice. - Specifically engineered for use in bicycle hydraulic disc brakes - Provides maximum fluid life and braking performance, even at low temperatures - Prevents foaming and overheating

Cleans bicycle chain quickly, easily, and effectively — without the hassle and mess of removing the chain from the bike. The Cyclone uses a large solvent reservoir, hundreds of rotating bristles, and a two-step cleaning process to get chains really clean, improve shifting performance, and extend the life of the chain and other expensive drivetrain parts. - Works with all multi-speed bikes (5, 6, 7, 8, 9, 10, 11, and 12-speed) as well as some single-speed models and e-bikes - Strong magnet at the bottom of the fluid reservoir holds metallic particles scrubbed from the chain - Special wicking sponge draws solvent from the chain as it exits, minimizing drips and mess - Sturdy handle makes the Cyclone easy to use and control - Holds 2 fluid ounces (59ml) of solvent

The HCW-16.3 is a combination 15mm pedal wrench and chain whip. Use for both pedal removal/installation and for cassette removal. Chain whip features improved compatibility with 5-speed to 12-speed mountain and road bike cassettes and freewheels. The HCW-16.3 is 10.75" long (27.3cm).

Designed and built to remove and install the lockring that retains front chainrings found on Shimano STEPS e-bike motors. - Fits Shimano STEPS E6100, E7000, E8000 and E9000 e-bike motor systems - For lockrings with 54mm outside diameter and 16 notches - Replacement for Shimano TL-FC39 tool - 36mm hex drive to be used with Park Tool TWB-36 Crow Foot and a torque wrench to properly measure torque - Constructed of 4140 heat-treated steel and plated for long life

- For all TRP and Tektro hydraulic braking systems - Non-corrosive mineral oil - Increased Boiling point to 270 degrees C - Decreased viscosity for better fluid flow

Wheels Manufacturing Sealed Bearing Extractor - 12mm Fits the following bearings: - 6001 - 6801 - 6901

Finish Line's Shop Quality Chain Cleaner is quick, efficient and easy to use. With it, you never have to remove your chain to keep it clean. Its triple rotating brushes and scrubber pads provide fast, thorough cleaning, while your hands stay clean. Plus, its rugged plastic construction is virtually unbreakable.

A precision CNC-machined aluminum tool for the installation and removal of select threaded bottom brackets with 12-notch tool fittings, including SRAM BSA DUB, Race Face Cinch, Rotor BSA30, and others. Manufactured in-house by Park Tool, anodized for easy identification and featuring a ratchet/torque wrench-compatible 3/8" drive. The BBT-79.3 features integrated threads for full compatibility with the Park Tool BBT-RS Bottom Bracket Tool Retaining System (sold separately). The BBT-RS uses an adjustable spring-based tension system to apply consistent, adjustable pressure to the tool, ensuring full engagement with the tool fitting and preventing slippage. Fits 12-notch threaded bottom bracket tool fittings with a major diameter (outside of notches) of 45–47 mm and a minor diameter (inside of notches) of 44 mm, including: - SRAM BSA DUB - Race Face Cinch - Rotor BSA30 - Zipp Vuma - Hawk Racing BB3086 - and more - 3/8" drive fitting

The EP-1 is purpose-built to securely install end caps onto brake, derailleur, and dropper post cables. The short tapered jaws with dual crimping positions make it ideal for crimping in tight, inaccessible spaces. Built from forged machined steel with vinyl-dipped handles.

For use with 1/2" Micro Bearing Press Shaft

Replacement 6/8mm Hex bit for both the Abbey BBQ Wood Handled Pedal Wrench and the Team Issue Pedal Wrench.

Tubeless tire plug kit plus CO2 head. - Tire plug tool - Tire plugs - CO2 head - Storage case - Mounting bracket - 5 year warranty

The Ergon TP1 Pedal Cleat Tool is the first tool for precisely and easily adjusting cycling shoes cleats. The ergonomically correct position of the feet on the pedals plays a crucial role in injury prevention and is also important for maximizing both performance and comfort.

Park's Adjustable Pin Spanner is the perfect tool for adjusting bottom brackets with threaded cups that have pin holes. It will also work on headset cups with holes and freewheel lockrings with them, too. This fine tool is made of chrome-plated steel and boasts hardened replaceable pins.

Performing the right maintenance on your SRAM and RockShox products not only ensures years of worry-free riding, but will also keep performance optimal and enhance your experience on the bike. Each service interval indicates the maximum number of riding hours designated for each type of recommended maintenance. Depending on the terrain and environmental conditions in your location, your riding style, and skill level, you may see more optimum performance if you service your SRAM and RockShox products at shorter intervals.